how to make a flute

Hold the flute horizontal to your body and place your lips next to the mouth opening. The length of the pipe determines the key.

Homemade Instruments For Kids Flute Homemade Instruments Homemade Musical Instruments Diy Musical Instruments

The extra fabric forms a flap to close the case.

. Clear up the debris from the gut using a file and sandpaper. Sand the opening to make it smoother and more pristine. If you are styling the flute out of cedar then saw the wood making. This area is will be the cork while the blowhole wont be placed far from it so dont cut.

As the flute is now taking on an identity and the exterior work is mostly done I stamp the instrument with my makers mark and the flutes serial number. Making a Native American style branch flute is a rewarding experience. The basic construction of a PVC flute is simple. Knock Out The Nodes.

Below you will find several items both helpful to making your own Native American Flutes as well as great example flutes to use as a starter into the understanding of how they are made. Shaping the root section to get the right size. Play the flute by first covering the four holes with your hand and blowing into the end farthest away from the holes. Blow air across the upper edge of the opening and experiment by.

For a flute that plays in the key of A use a 14-inch length of pipe. Then the maker creates the inner chambers. Place three fingers from one hand on the top three holes and three fingers from the other hand on the bottom three holes. Measure 1 12 inches from the mark and place the next finger.

Measure 5 inches from the bottom of the pipe and mark the spot for the first finger hole. One blown hole initiates the sound. For an F flute 18 inches and for a key of D 21 inches. Problem is most of the beginner makers have no clue about the potential dangers of working with PVC.

If you are making a flute out of bamboo make sure that the wood is mature and not green. Dry and store bamboo. This is normally about 14 to 30 inches. Fix a piece of well-fitting rubber into the flute and tap it a couple of times using a sledgehammer.

You can make a native American flute out of bamboo or red cedar wood both of which should be of excellent quality without any cracks on the surface that may spoil the flute. Or a maker can make the flute out of two pieces of wood. Choose an appropriate raw material for the flute. Flat refers to a pitch that is slightly lower than it is supposed.

Draw a second rectangle about 2 inches longer with the same width. With the help of a saw cut the wood measuring 18 inches the standard length of the flute. Play the flutes and using the fingering charts. Use the breath and its influence on the sound of the flute.

Blow over the flute. Knowing if your flute is flat or sharp will determine how you get it back into tune. Six holes provide the western seven-note scale. Choose the node that will become the cork and measure 2 cm out from the node and mark it using a pencil.

The maker eithers drill a flute with long drill bits or so called gun-drill which is a modified lathe. You have to knock out all the additional nodes to enable the flute to make great sounds. A flute that is out of tune might be flat or sharp. It is an ability to create wonderful instrument with your own hands.

Making a simple 6-hole flute from the elder wood Sambucus nigra. The slow air chamber and the. Hold the flute as if you were playing it and mark 5 inches from the bottom of your lowest hand. The finished flute will not kill you but what is produced during the process of making the flute is what gets you.

Usually a single piece of wood like 44 or 66 cm is cut into two 24 or 36 or two separate pieces are taken. The length will depend on the reach of your arms. Flutes made from hand drilled elder wood are part of cultural heritage of slavic nations -. It could be that the wood you use has more than one node.

The keys Although still meeting the specifications of sterling Silver ie 925 parts per thousand are pure silver Bright has the very great advantage of resisting fire-scale - a difficult-to-remove tarnish that can affect traditional sterling. Insert a block to the correct depth at the blown end and you have a flute. This post is the first article in a series of practical tutorials in the How to Make Branch Flute projectI will guide you. Cut outside of the node and not into it.

The rectangle should have a length that is about 2 to 3 inches longer than the case and a width that is the measurement of the width and depth combined with an extra inch for seam allowance. Cut the bamboo flute to the length you want according to the key. Many a beginner has started his flute journey with PVC. While a branch is split into two.

Hold the PVC pipe up to your mouth and angle it away from your body. Most beginners of flute making will try to construct a North American style flute out of PVC for their first flute. Making the flute to the key you want. Use the right tools you need for flute making.

Weve thrown a few other items like our Blue Bear Flutes T-shirt to show your support as well as our amp if your first flute turns out to be a masterpiece and you want the world to hear it.

How To Make A Bamboo Flute Bamboo Diy Bamboo Crafts Flute